![]() Figure 3 232e Mounting Height 6 Document #, Rev. In addition, use the anti-oxidant grease pack for the wire harness connectors. ![]() For outdoor installations, use a weatherproof backbox and seal the wire entry locations with silicone and provide a drain hole. An appropriate range is typically between 48 and 52 inches on center off the floor. ![]() Mounting height can vary depending on requirements. To properly size the mounting and wire access hole, use the installation template on the last page of this manual and on the unit s container. In addition, itcanbeflushmounteddirectlyto the wall surface by cutting a hole in the wall. Mounting Thekeypadisdesignedtobeflushmountedusingastandardsinglegang electrical box. 2.1ĥ Figure 1 Mounting a Sentrol 3012 Tamper Switch Figure 2 Mounting a Sentrol 3025T Tamper Switch Document #, RevĦ 3. The diagrams on the next page show the suggested mounting location for each device. Only a Sentrol 3012 or Sentrol 3025T tamper switch can be used. In addition, once the tamper device is activated, it must be configured so that it can only be reset from within the protected area. The lock must be a failsecure device, meaning the lock remains locked when power is removed. The tamper switch must activate if the keypad is removed from the box and must disconnect power from the lock. Listed tamper switch must be installed in the single gang box used for mounting the keypad. A minimum of three user codes must be programmed into the keypad for controlling access. Listed access control power limitedpowersupplymustbeusedtopowerthekeypad. All interconnecting devices (that is, door contacts, REX, locking devices, etc.) must be U.L. In addition, all wires and cables used must be stranded andshieldedu.l.listedand/orrecognizedwire. This system must be installed in accordance with the National Electrical code (NFPA70), local codes, and the authorities having jurisdiction. Specifications Parameter Range/Description Voltage VDC, VAC Current and Add 20 ma for each alarm relay Environment Indoor and Outdoor Temperature Tolerance -20 F to 130 F Dimensions 4.5" H x 2.75" W x 0.60" D Main Relay (Form C) Alarm Relays: Alarm Shunt, Propped Door, Forced Door Relays (Form C) Contact Rating: Contact Rating: 30VAC/DC 24V AC/DC Document #, RevĤ Section3.U.L.Requirements The232ekeypadisaU.L.Listedaccesscontrolunit.Thissection contains information regarding all the requirements necessary to meet U.L. All e style keypads mount to any standard single-gang electrical box or directly to any wall. Each e style keypad contains illuminated clear keys that make operation in low-light situations easy and accurate. In addition, each e style keypad uses hardened keys to assure long-term, high-quality performance. ![]() The electronics for each e keypad are conformal coated in the manufacturing process in order to provide this level of application flexibility. All e style keypads are designed for both indoor and outdoor flush mount applications. Also, the 232e Keypad contains inputs for door monitor and REX. Features and Product Description 1.1 Features Flush Mount Indoor and Outdoor Use Keypad Programmable Self-Contained Single Door Access Control Functionality Illuminated Backlit Keys Keypress Feedback via Built-In Sounder Bi-Color Red/Green LED Indicates Relay Status Yellow LED Indicates Program Mode 120 Users 10 to 30 Volt DC Operation 12 to 24 Volt AC Operation 2AmpMainRelay Lock Release Output With Timer Alarm Zone Shunt Relay Propped Door Alarm Relay Forced Door Alarm Relay Remote Trigger Input (REX) 5-Year Warranty 1.2 Product Description The model 232e Keypad is designed for security and is perfect for self-contained access control featuresoutputrelays to release the door lock, to shunt an alarm zone, and to trigger both a propped or forced door alert. Requirements Specifications Mounting Wiring 5.1 Wire Harness Configuration 5.2 Wiring the 232e Keypad to a Maglock (Fail-Safe) 5.3 Wiring the 232e Keypad to an Electric Strike (Fail-Secure) 5.4 Shunting a Normally Closed Zone 5.5 Wiring Remote Trigger as Request to Exit (REX) Button and Door Contacts 5.6 Installing the Plug-On Relay Board 5.7 Wiring the Standalone Access Control Relays Testing the Keypad Programming 7.1 Programming Main Relay Time 7.2 Programming Users 7.3 Programming Keypad Options Troubleshooting Programming Mode Loopback Warranty Manual Revision Date: 05/16/03 Firmware Version: 1.0b Document #, RevĢ 1. 1 IEI 232e Standalone TM Keypad Installation/ Programming Manual Contents Section 1: Section 2: Section 3: Section 4: Section 5: Section 6: Section 7: Section 8: Section 9: Section 10: Features and Product Description 1.1 Features 1.2 Product Description U.L. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |